Article temporary not available

Customer service until 6pm¹ - personal & close
DIY Videos - DIY Instructions

Starclic Project Click Vinyl - Kentucky Oak (119238)

0.50 mm wear layer - 42 industry (normal) - solid vinyl - bevelled edge (4-sided) - wood look wideplank brown

Item no.: 119238

Suitable for use in the commercial and industrial sectors.
Has a high dynamic load-bearing capacity.
Perfect for WW underfloor heating.
Fitted with bevelled edges (V-joint).
Low maintenance requirements.

Request alternative

Description

Technical data

DIY - Videos

Product description

Suitable for use in the commercial and industrial sectors.
Has a high dynamic load-bearing capacity.
Perfect for WW underfloor heating.
Fitted with bevelled edges (V-joint).
Low maintenance requirements.

Starclic Project click vinyl is the flooring product for the highest demands in the contract and commercial sectors.

Resistant
Easy to clean
Rich in variation

item no.: 119238

for commercial and industrial applications
Underfloor heating
Suitable for damp rooms
Ceramic coating
durable

Technical data

item no.	119238
Structure	Full vinyl
Installation type	click
installation pattern	Plank pattern (1-plank)
Wood type	Oak
Sorting (grain)	natural/classic
Joint	Beveled edge (4 sides)
Underfloor heating	suitable
Slip resistance	R10
Wear class	42 Industrial (moderate)
Wear layer	0,50 mm
Weight	18.3080 kg / Packing
Colour	brown
EAN	7640165927076
Piece per package	8
suitable for	Bath, Kitchen, Bedroom & living room, Hallway & Corridor
Look	Wood effect
Style	Modern
Special features	Suitable for humid rooms, Non-slip, Waterproof
Range of application	Commercial, Industrial
Length in mm	1210
Width in mm	190
Thickness in mm	5
Warranty	25 Jahre Privat, 5 Jahre Gewerbe
Shipping group	M
Click variant	UniClic
Package Content	1,84 m²

Print page

DIY step by step

Variant: DIY Instruction

button

1. substrate preparation

Check the subfloor. Any unevenness that exceeds 3 mm over a length of 1 m should be sanded down or filled with a floor levelling compound. Then clean the surface to be laid with a hoover.

CAUTION: Never install vinyl over a soft subfloor such as carpet, cork or any type of foam underlay.

button

2. acclimatisation

The vinyl planks should be stored horizontally in the room where it is to be installed for at least 48 hours before installation in the packages. This will allow the material to acclimatise to the room temperature and not "work" so hard after installation.

button

3. before laying

Before laying the floor, it is imperative to follow the official laying instructions, which are included in every package, otherwise any claim to warranty and guarantee will be void!

Before laying out the floor, check the wall you are starting on and make sure it is at right angles to the opposite wall. If the impact sound insulation is not already integrated, we now recommend spreading out the insulation.

button

4. installation instructions

Tips for the UniClic system: To achieve as uniform a floor appearance as possible, it is recommended to install panels from different packages mixed together. You should start laying in a corner (left) and starting from the wall. With the tongue side facing the wall, lay the first board. Angle the end of the second board into the first. In the second row, the plank is placed at an angle to the end face of the row already laid and folded down. As the board is folded down, the long side of the board will click into the existing board at an angle. With a little pressure, the click joints now snap into place. The transverse joints (front side) should be offset by at least 30 cm from row to row ("wild bond", half a plank length for tile formats). You can use a tapping block and a light tap on the long side of the plank to help it along. To cut a plank, now take measurements and mark the plank. Then take an angle and tear the plank with a multi-purpose knife/cutter and break it off.

button

5. finishing the last row

Place the spacers on walls, door frames, fixed wall cabinets, kitchen units, etc. so that you have an expansion gap of approx. 5-10mm for underfloor movement or expansion of the product. To install the last row, it is recommended to use the floor layer's jointing iron from the accessories. When using skirting boards, make sure that the expansion joint is covered by the skirting board. If the floor is sealed, e.g. in the bathroom, the PE round cord is now inserted into the expansion joint and the floor sealed with a silicone joint.

button

6. attach skirting boards

Finally, cut off the PU film approx. 2 cm high and attach the skirting boards.

Starclic Project Click Vinyl - Kentucky Oak (119238)

Product description

Technical data

DIY step by step

Helpful Videos

Click vinyl flooring installation guide

Laying vinyl flooring on tiles, how wide and deep can the joint be?

Is click vinyl flooring waterproof, and can it be used in bathrooms?

Checking the subfloor before installing flooring

The 10 most common mistakes when installing vinyl flooring - is it possible?

Laying vinyl flooring on old floorboards

Damp room flooring for bathrooms - sealing the flooring

Fill uneven tiles and joints

Laying floor along heating pipe

Vinyl flooring wear layer 0.3 or 0.5mm. Does a high wear layer protect against scratches?