Article temporary not available

Customer service until 6pm¹ - personal & close
DIY Videos - DIY Instructions

Starclic Stone click vinyl - Bologna (119269)

Vinyl tile in stone look and all-round bevelled edge

Item no.: 119269

Creates a special look in the rooms.
Long service life.
Resistant to dirt.
Resistant to moisture.

Request alternative

Description

Technical data

DIY - Videos

Product description

Creates a special look in the rooms.
Long service life.
Resistant to dirt.
Resistant to moisture.

In addition to visual requirements, durability often takes centre stage when it comes to flooring. Vinyl floors from the planeo stone collection offer an adequate solution for this. They have almost the same properties as a stone floor.

Not only inexpensive
Durable and wear-resistant

item no.: 119269

robust & durable
insensitive to dirt
underfloor heating

Technical data

item no.	119269
Length in mm	605
Width in mm	305
Thickness in mm	5
Wear layer	0,50 mm
Wear class	42 Industrial (moderate)
Joint	Beveled edge (4 sides)
Warranty	25 Jahre Privat, 5 Jahre Gewerbe
suitable for	Bath, Kitchen, Bedroom & living room, Hallway & Corridor
installation pattern	Tile format
Installation type	click
Look	Concrete effect, Stone effect, Tile effect
Sorting (grain)	natural/classic
Underfloor heating	suitable
Special features	Pet Friendly, Suitable for humid rooms, Waterproof
EAN	7640165927137
Piece per package	10
Structure	Full vinyl
Slip resistance	R10
Shipping group	M
Weight	18,31 kg / Packing
Colour	grey
Style	Classic
Range of application	Commercial, Industrial
Click variant	UniClic
Package Content	1,84 m²

Print page

DIY step by step

Variant: DIY Instruction

button

1. substrate preparation

Check the subfloor. Any unevenness that exceeds 3 mm over a length of 1 m should be sanded down or filled with a floor levelling compound. Then clean the surface to be laid with a hoover.

CAUTION: Never install vinyl over a soft subfloor such as carpet, cork or any type of foam underlay.

button

2. acclimatisation

The vinyl planks should be stored horizontally in the room where it is to be installed for at least 48 hours before installation in the packages. This will allow the material to acclimatise to the room temperature and not "work" so hard after installation.

button

3. before laying

Before laying the floor, it is imperative to follow the official laying instructions, which are included in every package, otherwise any claim to warranty and guarantee will be void!

Before laying out the floor, check the wall you are starting on and make sure it is at right angles to the opposite wall. If the impact sound insulation is not already integrated, we now recommend spreading out the insulation.

button

4. installation instructions

Tips for the UniClic system: To achieve as uniform a floor appearance as possible, it is recommended to install panels from different packages mixed together. You should start laying in a corner (left) and starting from the wall. With the tongue side facing the wall, lay the first board. Angle the end of the second board into the first. In the second row, the plank is placed at an angle to the end face of the row already laid and folded down. As the board is folded down, the long side of the board will click into the existing board at an angle. With a little pressure, the click joints now snap into place. The transverse joints (front side) should be offset by at least 30 cm from row to row ("wild bond", half a plank length for tile formats). You can use a tapping block and a light tap on the long side of the plank to help it along. To cut a plank, now take measurements and mark the plank. Then take an angle and tear the plank with a multi-purpose knife/cutter and break it off.

button

5. finishing the last row

Place the spacers on walls, door frames, fixed wall cabinets, kitchen units, etc. so that you have an expansion gap of approx. 5-10mm for underfloor movement or expansion of the product. To install the last row, it is recommended to use the floor layer's jointing iron from the accessories. When using skirting boards, make sure that the expansion joint is covered by the skirting board. If the floor is sealed, e.g. in the bathroom, the PE round cord is now inserted into the expansion joint and the floor sealed with a silicone joint.

button

6. attach skirting boards

Finally, cut off the PU film approx. 2 cm high and attach the skirting boards.

Starclic Stone click vinyl - Bologna (119269)

Product description

Technical data

DIY step by step

Helpful Videos

Click vinyl flooring installation guide

Laying vinyl flooring on tiles, how wide and deep can the joint be?

Is click vinyl flooring waterproof, and can it be used in bathrooms?

Checking the subfloor before installing flooring

The 10 most common mistakes when installing vinyl flooring - is it possible?

Laying vinyl flooring on old floorboards

Damp room flooring for bathrooms - sealing the flooring

Fill uneven tiles and joints

Laying floor along heating pipe

Vinyl flooring wear layer 0.3 or 0.5mm. Does a high wear layer protect against scratches?