Article temporary not available

Customer service until 6pm¹ - personal & close
DIY Videos - DIY Instructions

Kährs Parquet Flooring - Rifugio Collection Auronzo Oak (151XDDEKF9KW195)

Name: Kährs Parquet Flooring - Rifugio Collection Auronzo Oak (151XDDEKF9KW195)
Brand: Kährs
SKU: 151XDDEKF9KW195
Availability: InStock

3,5 mm Wear layer - 3-layer - Beveled edge (4 sides) - Click system 5S - Plank pattern - oiled - brushed - brown

Item no.: 151XDDEKF9KW195

Request alternative

Description

Technical data

DIY - Videos

Product description

Kährs

The traditional company Kährs has been offering complete flooring solutions for private homes and commercial properties since 1857. Sweden's leading wooden flooring manufacturer invented finished parquet (multi-layer parquet) and glueless interlocking. Kährs created a patented innovation in 1941 with a multilayer wood floor that is stable and environmentally friendly. Kährs' multi-layer parquet is made from renewable raw materials and can be recycled. In 1958, Kährs launched the first factory lacquered parquet floor. The company is the first parquet manufacturer to introduce a solvent-free lacquer. In 2000, Kährs offered Woodlock, the first click-jointed parquet floor. Kährs is part of Kährs Group, the global market leader in wood flooring and PVC-free resilient flooring.

item no.: 151XDDEKF9KW195

Technical data

item no.	151XDDEKF9KW195
Manufacturer	Kährs
Collection	Rifugio Collection
Length in mm	1900
Width in mm	190
Thickness in mm	15
Wear layer	3,5 mm
Joint	Beveled edge (4 sides)
installation pattern	Plank pattern (1-plank)
Installation type	click
Wood type	Oak
Sorting (grain)	lively/rustic
Underfloor heating	suitable
EAN	7393969046862
Piece per package	6
Structure	3-layer
Click system	5S
Shipping group	L
Weight	16,70 kg / Packing
Colour	brown
Surface treatment	oiled
Range of application	Residential
Package Content	2,17 m²

Downloads

Print page

DIY step by step

Variant: DIY-Instruction

button

1. substrate check

The subfloor should be permanently dry, load-bearing and even.

ATTENTION: Never lay parquet over a soft subfloor, e.g. over carpet, cork or any type of foam underlay.

button

2. acclimatisation

The planks should be stored horizontally in the room where they are to be installed for at least 48 hours before the installation in the packages. This will allow the material to acclimatise to the room temperature and not "work" so hard after the installation.

Before laying, it is imperative that the official laying instructions, which are included in each package, are followed, otherwise any claim to warranty and guarantee will be invalidated!

button

3. subfloor preparation

Then clean the surface to be laid with a hoover. Any unevenness exceeding 3 mm per linear metre is sanded down and filled with a floor levelling compound.

Click:

button

4. before laying

Spread out the PE foil with an overlap of approx. 10 cm and tape it down.Now you can lay out the strips of impact sound insulation butt to butt against the laying direction of the floor covering and fix all overlaps with aluminium tape. The foil side should always face upwards.

Tip: Open several packages of the parquet at the same time and mix the planks to achieve an optimal installation pattern.

button

5. laying instructions

Lay the first plank well aligned on the subfloor, taking the edge distances into account. You can start laying the floor on the left side of the room. In the first row, the plank is clicked in with the front side. Use a rubber mallet to tap lightly on the front side so that the click connection snaps in well. In the next row, the planks are first clicked in with the long side and then the ends can be fixed by tapping lightly. To cut a plank, now take measurements and mark the plank. This is then cut with a jigsaw or crosscut saw.

ATTENTION: There must always be a gap of approx. 10 mm between the flooring and the wall and between the flooring and all fixed components.

button

6. last row

Cut the planks of the last row to size and click them in place using a pull iron. Finally, the planks can be tapped down again with a hammer.

button

7. finish

The PU foil is now cut approx. 2 cm high and the skirting boards can be fitted. Here there is the click or glue variant.

Glue:

button

4 Before gluing

Lay out the first two rows of planks and make marks in the subfloor with a pencil. The planks can be cut to size using a crosscut saw.

Tip: Open several packages of the parquet at the same time and mix the planks to achieve an optimal installation pattern.

button

5. laying instructions

Now pick up the planks again and apply the adhesive up to the marking with a notched trowel. Align the first plank and place it in the wet bed. The second plank is clicked into the already lying plank with the front side. The boards of the next row are laid first with the long side, then with the short side. Then the adhesive for the next two rows can be applied and the planks can be glued.

ATTENTION: There must always be a gap of approx. 10 mm between the flooring and the wall as well as to all fixed components.

button

6. last row

Finally, you can attach the skirting boards.

Kährs Parquet Flooring - Rifugio Collection Auronzo Oak (151XDDEKF9KW195)

Product description

Technical data

Downloads

DIY step by step

Helpful Videos

planeo parquet installation instructions

Glue down parquet - glue down parquet flooring on wooden subfloor

Floating installation parquet plank oak 1-plank UV-oiled

Discolouration of parquet - UV radiation and the effects

Parquet in the kitchen

Oiled parquet. Advantages and disadvantages

Varnished parquet. Advantages and disadvantages

Store parquet correctly - this is what you should consider before laying!

Laying herringbone parquet yourself is easy - herringbone floorboards to click on