MSRP 1.500,00 €

Package price (120 m²): 1.308,00 €

Price 1 m²: 10,90 €

Customer service until 6pm¹ - personal & close
DIY Videos - DIY Instructions

Gerflor PVC Floor - BOOSTER SPA SILVER GREY 4m x 30m - 1919

Economical & comfortable CV flooring Quality flooring with robust vinyl backing

Item no.: 13751919

Can be used in all living spaces.
Qualified for hot water underfloor heating (up to 28°C).
Suitable for kitchen and bathroom.
Thickness: 2.6mm incl. comfort foam backing.
Dimensionally stable glass fleece layer.
Easy to clean with water and neutral detergent.
Formaldehyde and solvent-free.
Without harmful plasticisers.
100% recyclable

Article is only available in whole rolls!

Offer request

Description

Technical data

Product description

Can be used in all living spaces.
Qualified for hot water underfloor heating (up to 28°C).
Suitable for kitchen and bathroom.
Thickness: 2.6mm incl. comfort foam backing.
Dimensionally stable glass fleece layer.
Easy to clean with water and neutral detergent.
Formaldehyde and solvent-free.
Without harmful plasticisers.
100% recyclable

Article is only available in whole rolls!

With the PVC floor Booster from Gerflor you have a floor with a long service life that can be used in all living spaces.

Environmentally friendly & healthy for living
Hard-wearing all-rounder
Preparation
Full-surface bonding

A suitable dispersion adhesive should be used to bond the floor covering. Use a fine-toothed spatula (A2) and weld the seams with cold welding paste.

Gerflor

Gerflor, a leading flooring manufacturer, has a 70-year history of producing resilient floor coverings for residential and commercial applications. The French company was founded in Lyon in 1937 and always focused on innovation, healthy materials and aesthetic floor design when developing new flooring solutions. Gerflor is right about its success - numerous awards attest to the first-class quality, the design, and the environmentally friendly aspect of Gerflor products. The Red Dot Award competition honors Gerflor's Creation 70 with the Red Dot Award for Product Design 2016.

item no.: 13751919

environmentally friendly
suitable for humid rooms
comfortable
easy to clean & maintain
non-slip
quiet

Technical data

item no.	13751919
Manufacturer	Gerflor
Collection	BOOSTER
Width in mm	4000
Thickness in mm	2.6
Wear layer	0,25 mm
Wear class	31 Commercial (light)
suitable for	Bath, Bedroom & living room, Hallway & Corridor
installation pattern	Cube pattern
Installation type	glue
Look	Tile effect
Special features	Vinyl back
EAN	3475710362248
Piece per package	1
Material	CV
Shipping group	M
Weight	207,00 kg / Packing
Colour	brown
Style	Retro
Package Content	120 m²

Print page

DIY step by step

Variant: DIY-Instruction

button

1. substrate check

The first step is to check the subfloor. Sand down any unevenness and fill it with a floor levelling compound. Then clean the surface to be laid with a hoover.

CAUTION: Never install PVC flooring over a soft subfloor, e.g. over carpet or any type of foam underlay.

button

2. before installation

PVC flooring should be stored in the room where it is to be installed for at least 24 hours before the installation. This will allow the material to acclimatise to the room temperature and not "work" so hard after the installation.

For loose laying of an area larger than 20 m², we recommend taping the edge of the walls.

Before laying, it is imperative to follow the official laying instructions, which are included in every package, otherwise any claim to warranty and guarantee will be void!

button

3. cutting to size

Tip: To achieve as uniform a floor appearance as possible, lay the strips in relation to each other so that the patterns match exactly and the strips overlap at the seam. Unpack the roll and roll it out on the subfloor. Use a hooked blade knife to roughly pre-cut the strips.

ATTENTION: There must always be a gap of approx. 3 cm between the flooring and the wall and between the flooring and all fixed components.

button

4. laying instructions

4.1 Loose laying

Stick the tape strips to all edge areas and remove the foil on the back of the tapes area by area. Now fix the floor by pressing lightly. Make a double cut at the joint of the strip. To do this, lay the sheet overlapping and cut the sheet to fit exactly along the joint. You can then make the final cut with an edge distance of approx. 2 mm. The floor should be free of tension when cutting and no objects should lie on the PVC floor.

4.2 Gluing

Apply the adhesive evenly to the subfloor in strips using a notched trowel. Please observe the flash-off times specified in the data sheet. Now lay the strips in the wet bed and rub down the PVC covering. Make the final cut with an edge distance of approx. 2 mm. Finally, the substrate can be rolled with a roller to avoid air bubbles.

button

5. finishing loose laying

First, tape over the joints of the strips with masking tape. The masking tape can then be cut at the joint and now the strips are welded together with a cold welding adhesive. After approx. 1 hour, the masking tape can be removed.

button

6. attaching the skirting boards

Finally, you can attach and seal the skirting boards. PVC flooring can also be attached to existing skirtings with a mounting adhesive.