Package price (100 m²): 2.395,00 €

Price 1 m²: 23,95 €

Customer service until 6pm¹ - personal & close
DIY Videos - DIY Instructions

Gerflor PVC flooring - TEXLINE HQR SEASIDE BLUE - 2216

Economical high-tech floor with textile backing for private & commercial use

Item no.: TexHQR2216_conf

Qualified for hot water underfloor heating (up to 28°C).
Can be loosely laid up to 20m² without fixing.
Low noise (16db).
Can be laid on almost all existing floors (see installation instructions).
Suitable for kitchen and bathroom.
Thickness: 3.1mm incl. textile backing.

Offer request

Description

Technical data

Product description

Qualified for hot water underfloor heating (up to 28°C).
Can be loosely laid up to 20m² without fixing.
Low noise (16db).
Can be laid on almost all existing floors (see installation instructions).
Suitable for kitchen and bathroom.
Thickness: 3.1mm incl. textile backing.

With the Texline HQR PVC floor from Gerflor, you have a quality product with a long service life that can be used in both private and commercial rooms.

Environmentally friendly & healthy
Very hard-wearing
Installation methods

The floor can be glued down over the entire surface or, for areas up to 20m², it can also be laid loosely. Under certain conditions, Texline can be laid on top of existing coverings such as tiles or wooden floorboards. (Please follow the manufacturer's installation instructions).

Gerflor

Gerflor, a leading flooring manufacturer, has a 70-year history of producing resilient floor coverings for residential and commercial applications. The French company was founded in Lyon in 1937 and always focused on innovation, healthy materials and aesthetic floor design when developing new flooring solutions. Gerflor is right about its success - numerous awards attest to the first-class quality, the design, and the environmentally friendly aspect of Gerflor products. The Red Dot Award competition honors Gerflor's Creation 70 with the Red Dot Award for Product Design 2016.

item no.: TexHQR2216_conf

environmentally friendly
suitable for humid rooms
hard-wearing
pleasant walking comfort
warm and flexible underfoot
easy cleaning & maintenance
non-slip
quiet

Technical data

item no.	TexHQR2216_conf
Manufacturer	Gerflor
installation pattern	2-plank
Thickness in mm	3.1
Installation type	glue
Material	CV
suitable for	Bath, Kitchen, Bedroom & living room, Hallway & Corridor
Wood type	Oak
Wear layer	0,50 mm
Piece per package	1
Collection	TEXLINE HQR
Look	Wood effect
Style	Country house
Special features	Textile back
Wear class	41 Industrial (light)
Range of application	Residential
Shipping group	M
Package Content	100 m²

Print page

DIY step by step

Variant: DIY-Instruction

button

1. substrate check

The first step is to check the subfloor. Sand down any unevenness and fill it with a floor levelling compound. Then clean the surface to be laid with a hoover.

CAUTION: Never install PVC flooring over a soft subfloor, e.g. over carpet or any type of foam underlay.

button

2. before installation

PVC flooring should be stored in the room where it is to be installed for at least 24 hours before the installation. This will allow the material to acclimatise to the room temperature and not "work" so hard after the installation.

For loose laying of an area larger than 20 m², we recommend taping the edge of the walls.

Before laying, it is imperative to follow the official laying instructions, which are included in every package, otherwise any claim to warranty and guarantee will be void!

button

3. cutting to size

Tip: To achieve as uniform a floor appearance as possible, lay the strips in relation to each other so that the patterns match exactly and the strips overlap at the seam. Unpack the roll and roll it out on the subfloor. Use a hooked blade knife to roughly pre-cut the strips.

ATTENTION: There must always be a gap of approx. 3 cm between the flooring and the wall and between the flooring and all fixed components.

button

4. laying instructions

4.1 Loose laying

Stick the tape strips to all edge areas and remove the foil on the back of the tapes area by area. Now fix the floor by pressing lightly. Make a double cut at the joint of the strip. To do this, lay the sheet overlapping and cut the sheet to fit exactly along the joint. You can then make the final cut with an edge distance of approx. 2 mm. The floor should be free of tension when cutting and no objects should lie on the PVC floor.

4.2 Gluing

Apply the adhesive evenly to the subfloor in strips using a notched trowel. Please observe the flash-off times specified in the data sheet. Now lay the strips in the wet bed and rub down the PVC covering. Make the final cut with an edge distance of approx. 2 mm. Finally, the substrate can be rolled with a roller to avoid air bubbles.

button

5. finishing loose laying

First, tape over the joints of the strips with masking tape. The masking tape can then be cut at the joint and now the strips are welded together with a cold welding adhesive. After approx. 1 hour, the masking tape can be removed.

button

6. attaching the skirting boards

Finally, you can attach and seal the skirting boards. PVC flooring can also be attached to existing skirtings with a mounting adhesive.