Gerflor self adhesive Vinyl - Senso Premium Balade Grey (35790910)

0,30 mm Wear layer - 23 Residential (heavy) - Full vinyl - Micro bevel - Wood effect - Plank pattern - brown

Item no.: 35790910

With strong self-adhesive layer.
With reinforced structure.
Easy and flush to lay.
Resistant to deformation.

Request alternative

Description

Technical data

Product description

With strong self-adhesive layer.
With reinforced structure.
Easy and flush to lay.
Resistant to deformation.

The self-adhesive Senso Premium planks have an extra strong adhesive layer and an extra strong construction to simplify the installation, but also to give you a long-lasting benefit from the Gerflor vinyl floor.

Reinforced construction
Easy installation
Easy-care and antistatic

Thanks to the PUR+ surface finish, Senso Premium is easy to clean and antistatic. For normal household cleaning, wiping with normal water is usually sufficient. For heavier soiling, we recommend special PU cleaners.

Gerflor

Gerflor, a leading flooring manufacturer, has a 70-year history of producing resilient floor coverings for residential and commercial applications. The French company was founded in Lyon in 1937 and always focused on innovation, healthy materials and aesthetic floor design when developing new flooring solutions. Gerflor is right about its success - numerous awards attest to the first-class quality, the design, and the environmentally friendly aspect of Gerflor products. The Red Dot Award competition honors Gerflor's Creation 70 with the Red Dot Award for Product Design 2016.

item no.: 35790910

antistatic
easy to install
dimensionally stable
underfloor heating

Technical data

item no.	35790910
Manufacturer	Gerflor
Structure	Full vinyl
Length in mm	1219
Width in mm	184
Thickness in mm	2.5
Colour	brown
Look	Wood effect
Piece per package	11
Collection	Senso Premium
Installation type	self-adhesive
installation pattern	Plank pattern (1-plank)
suitable for	Bath, Kitchen, Bedroom & living room
Sorting (grain)	lively/rustic
Joint	Micro bevel
Wood type	Larch
Wear class	23 Residential (heavy)
Wear layer	0,30 mm
EAN	3475710431418
Shipping group	S
Weight	11,51 kg / Packing
Range of application	Residential
Package Content	2,47 m²

Print page

DIY step by step

button

1. substrate preparation

The substrate should be permanently dry, load-bearing and even. Any unevenness is sanded down and filled with a floor levelling compound. Depending on the substrate, the preparation procedure may vary. Please check the installation instructions to see which preparation is necessary for your subfloor. The surface to be laid can then be cleaned with a hoover.

button

2. acclimatisation

The vinyl planks should be stored horizontally in the room in which they are to be installed for at least 24 hours before the installation in the packages. This will allow the material to acclimatise to the room temperature and not "work" so hard after the installation.

Before laying, it is imperative that the official laying instructions, which are included in each package, are followed, otherwise any claim to warranty and guarantee will be invalidated!

button

3. before laying

Apply the bonding primer to the substrate in preparation for bonding to improve adhesion.

Tip: To achieve as uniform a floor appearance as possible, it is recommended to install panels mixed from different packages.

button

4. installation instructions

You can start with the installation on the left side of the room or in the middle of the room. First remove the protective foil and lay the first plank well aligned on the subfloor. Now press the plank firmly into place. The next planks are laid butt to butt with the planks already in place. Please note the laying direction on the back of the planks. To cut a plank, now take measurements and set the marks. Then take an angle and tear the plank with a cutter knife and break it off.

Attention: A distance of approx. 5 mm must always be maintained between the flooring and the wall as well as to all fixed components.